Oct 01 2014

Fritschi fixes Vipec’s Toe Woes


Vipec's toe gets a make over. 1) Thicker pins: M5 to M6. 2) Spring-loaded locking pin. 3) Self centering jaws. 4) Improved toe clip

Vipec’s toe gets a make over.
1) Thicker pins: M5 to M6. 2) Spring-loaded locking pin.
3) Self centering jaws. 4) Improved toe clip

Based on feedback from retailers and early adopters, Fritschi’s Vipec, their first 2-pin tech binding, will see four modifications to the toe unit this season. The most noticeable change is to the pins, which will now be thicker, a tad longer, and with an improved adjustment locking mechanism. Less obvious, but perhaps more important, is the addition of plastic guides inside the pin arms to make getting in and out of the binding much easier. Lastly, a clip that snaps onto the toe release lever will now come pre-mounted for a better touring release with square-toed boots.

Introductory Woes

The Vipec is the first tech binding to provide lateral release at the toe. This capability requires the pins to set inside the inserts with a tighter tolerance than the dimensions of some inserts may allow. Insert dimensions may vary from boot to boot by as much as 1.2 mm. To account for that disparity Fritschi made the depth of the left pin adjustable by retailers installing the binding. Furthermore, retailers were expected to secure the lock nut on the pin with Loctite™ so it wouldn’t come loose after installation. Unfortunately, not everyone followed directions and early reports indicated pins were falling out in the field.

Field Repair

Fritschi responded immediately by shipping all bindings with Loctite™ already applied. In the majority of cases the pins don’t need any adjustment. If the pins didn’t seat properly in a boot, retailers were given instructions for making the adjustment and reapplying Loctite™ 263. This did resolve the problem of pins falling out, and raised awareness of the need to check the pin gap relative to a boots insert width.

The Fix

The new locking mechanism for Vipec's adjustable toe pin.

The new locking mechanism for Vipec’s adjustable toe pin.

Based on requests by their global distribution partners Fritschi is upping the ante moving forward. New Vipec bindings now have the adjusting pin on the right side. The angular forces on the pin will now incrementally tighten the lock nut, not loosen it. Furthermore, in addition to Loctite™, a mechanical spring-loaded pin will hold the lock nut in place.

updated 06oct14

From early photos and diagrams provided I can only speculate this will act like a cotter pin. The photo above shows that the pin keeps the screw head locked in position. It also means the adjustment is limited to a half rotation, but that should be fine enough. (end update) And finally, even though there were no reports of mechanical pin failure the diameter of the pins will increase from M5 to M6, making them inherently stronger.

Plastic tabs remain in position to guide your boot toe in.

Plastic tabs remain in position to guide your boot toe in.

While these changes should calm any fears of pins falling out in the field, the issue more people noticed is Vipec’s version of fiddle factor for getting in and out of the binding. Molded plastic guides will now adorn the lower half of the pin arms to help center them about the boot. Fritschi claims this makes getting in and out easier. I haven’t actually tried it yet, but it looks like a solid improvement.

At Vipec’s introduction two clips were available to add to the front release lever. These provided a surface for a boot to contact in the event of a forward fall to prevent the jaws opening up prematurely. Based on experience, the thicker clip will be included as standard, the thinner clip will be discontinued.

All’s well

The fix is in for Vipec.

The fix is in for Vipec.

Except for the toe clip, I reported on all these shortcomings in a comprehensive review of the Vipec in May 2014. It is great to see Fritschi offer improvements to address them. Alpine skiers don’t obsess over their bindings much since they tend to disappear once you’re in them. Touring bindings will never be that fortunate since they need to do more than merely hold onto your boot while sliding down a slope, they also need to hold on while letting you walk uphill too. With these improvements the Vipec is one step closer to becoming a commodity you can rely on without giving it much thought.

The potential for snow to creep inside the heel unit remains, and unless you tour where the snow is routinely damp, this should be a rare condition. If it does happen it will be difficult to either lock the heel in downhill mode, or vice versa. To fix that, you need to remove the snow, either by removing the heel unit from the slider track to clear it out, or knocking it loose, or waiting for it to melt out. In any case, don’t force it or you’ll break the black lever arm.

More credible commentary to follow later this winter after a pair of the updated Vipec’s are given a real field test.

© 2014
Related Posts
Devilish Details of Fritschi’s Vipec
First Look: Fritschi’s Vipec

  • Pingback: Review: The devilish details of Fritschi-Diamir's Vipec 12, AT Binding | EarnYourTurns

  • Pingback: AT Tech Binding Roundup for 2014/15 | EarnYourTurns

  • Dostie

    Without actually testing it the two major changes to the 2015 Vipec appear to solidly address the issues of the adjustment pin working loose, and aligning your boot for less fiddle factor getting in. More when we get some time on snow to confirm these improvements, but they certainly look good.

  • Pat

    Skiing an “early” version of Vipec yesterday out on Spearhead Glacier (behind Whistler) my toe pin broke or fell out. Tried tying, taping, strapping boot to ski but didn’t work. 5 hours of boot packing to get out. Was very dark and cold when finally back to resort runs. Toe pin is the critical component of these bindings.

  • Pingback: Maria Smith

  • neversummerpb

    My lock-nuts keep coming off the right toe pin. I have 2nd gen bindings – 4 of them. The nut keeps coming off. If I find the right size nut, should i apply loctite to it and feel safe. I spend a lot of time skiing huts far removed from road or any other access. Working bindings are imperative.

  • Dostie

    Nothing man made is ever flawless. Yeah – use Loctite. It will probably work, but I’d still include a few nuts in a repair kit, just in case.